SIIG, INC. SI-1414RI Modem Type Data (synchronous/asynchronous)/Fax Maximum Data Rate 14.4Kbps Maximum Fax Rate 14.4Kbps Data Bus Internal Fax Class Class I & II Data Modulation Protocol ITU-T V.22, V.22bis, V.23, V.32, V.32bis Fax Modulation Protocol ITU-T V.17, V.21CH2, V.27ter, V.29 Error Correction/Compression MNP5, V.42, V.42bis [Image] BASE I/O ADDRESS SELECTION Port J1/A J1/B J1/C COM1: (3F8h) Open Open Open COM2: (2F8h) Closed Open Open COM3: (3E8h) Open Closed Open » COM4: (2E8h) Closed Closed Open COM5: (2F0h) Closed Open Closed COM6: (3E0h) Open Closed Closed COM7: (2E0h) Closed Closed Closed INTERRUPT SELECTION IRQ J1/D J1/E J1/F J1/G J1/H 3 Open Closed Open Open Open 4 Open Open Closed Open Open 5 Open Open Open Closed Open 7 Open Open Open Open Closed 9 Closed Open Open Open Open Proprietary AT Command Set ACCEPT RELIABLE MODE Type: Immediate Format: AT [cmds] \U Example: AT \U Description: Accepts remote modem’s request for reliable link. AUTO-RELIABLE FALLBACK CHARACTER Type: Configuration Format: AT [cmds] %An [cmds] Example: AT%A20 Default: 19 Range: 0-127 Unit: ASCII Description: Sets the character used as the auto-reliable fallback character. %A0 will disable this function. BREAK SEND Type: Configuration Format: AT [cmds] \Bn [cmds] Example: AT \B3 &W Range: 1-9 Unit: .1 second Description: Sends break to modem. BREAK TYPE Type: Configuration Format: AT [cmds] \Kn [cmds] Example: AT \K1 Description: Configures action of break signal. Command Function \K0 Online command mode enabled, send no break to remote modem. \K1 Break sent to remote modem and buffered cleared. \K2 Online command mode enabled, send no break to remote modem. \K3 Send break to remote modem immediately. \K4 Online command mode enabled, send no break to remote modem. \K5 Send break with transmitted data. COMMUNICATIONS MODE Type: Configuration Format: AT [cmds] &Mn [cmds] Example: AT &M0 &E1 Description: Selects communications mode. Command Function &M0 Asynchronous mode. &M1 Synchronous connect mode and asynchronous off-line command mode. &M2 Synchronous connect mode and asynchronous off-line command mode and set DTR high. &M3 Synchronous connect mode. » &M5 V.42 connection enabled. COMPRESSION Type: Configuration Format: AT [cmds] %Cn [cmds] Example: AT *EC0 %C1 *AP0 Description: Selects data compression. Command Function %C0 Data compression disabled. » %C1 Data compression enabled. CONNECT MODE Type: Configuration Format: AT [cmds] \Nn [cmds] Example: AT \N1 DT555-1212 Description: Sets connect mode. Command Function \N0 Normal mode. \N1 Direct mode. \N2 Reliable mode. \N3 Auto-reliable mode. \N4 V.42bis reliable mode with phase detection. \N5 V.42bis auto-reliable mode with phase detection. \N6 V.42 reliable mode without phase detection. \N7 V.42 auto-reliable mode without phase detection. CONVERT TO RELIABLE MODE Type: Immediate Format: AT [cmds] \O [cmds] Example: AT \O Description: Initiates reliable mode link. ECHO DATA Type: Configuration Format: AT [cmds] \En [cmds] Example: AT \E0 Description: Enables modem to echo received data. Command Function » \E0 Data echo disabled. \E1 Data echo enabled. FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] &Kn [cmds] Example: AT *MF1 *DF1 &K5 Description: Sets type of flow control used by modem. Command Function &K0 Flow control disabled. &K3 CTS/RTS flow control enabled. » &K4 XON/XOFF flow control enabled. &K5 XON/XOFF pass-through flow control enabled. FLOW CONTROL TYPE Type: Configuration Format: AT [cmds] \Qn [cmds] Example: AT \Q0 A Description: Sets type of flow control used by modem. Command Function \Q0 Flow control disabled. \Q1 XON/XOFF flow control enabled. \Q2 CTS flow control enabled. » \Q3 CTS/RTS flow control enabled. LOCK SERIAL PORT Type: Configuration Format: AT [cmds] \Jn [cmds] Example: AT %L3 %B14 \J0 Description: Sets operation of serial port speed. Command Function » \J0 Serial speed locked. \J1 Serial speed follows connect speed. MAXIMUM BLOCK SIZE FOR TRANSMISSION Type: Configuration Format: AT [cmds] \An [cmds] Example: AT \A3 %C1 Description: Sets the maximum transmittable block size. Command Function \A0 Maximum MNP block size is 64 characters. \A1 Maximum MNP block size is 128 characters. \A2 Maximum MNP block size is 192 characters. » \A3 Maximum MNP block size is 256 characters. MNP EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] \Vn [cmds] Example: AT \V1 %C1 Description: Selects MNP extended result codes. Command Function \V0 MNP extended result codes disabled. » \V1 MNP extended result codes enabled. V.42 EXTENDED RESULT CODES Type: Configuration Format: AT [cmds] \Wn [cmds] Example: AT \W1 %C1 Description: Selects V.42 extended result codes. Command Function \W0 V.42 extended result codes disabled. » \W1 V.42 extended result codes enabled. XON/XOFF PASS-THROUGH Type: Configuration Format: AT [cmds] \Xn [cmds] Example: AT \X0 Description: Selects whether XON/XOFF signals are sent to remote modem. Command Function \X0 XON/XOFF signals trapped by local modem. \X1 XON/XOFF passed through local modem.